The pipe fitting tee produced by Hebei Shengtian Group must undergo strict testing before leaving the factory

Views : 645
Author : admin
Update time : 2024-02-06 09:03:31

  The Gost 17376 Butt Welding Reducing Pipe Fitting Tees produced by Hebei Shengtian Pipe Fittings Group Co., Ltd. will be re-tested before leaving the factory before being shipped to customers.

  1. The Gost 17376 Butt Welding Reducing Pipe Fitting Tee material must be inspected before leaving the factory.

  After the Gost 17376 Butt Welding Reducing Pipe Fitting Tee is produced and before leaving the factory, some tee material inspections must be done to check whether the pipe fitting tee material is correct. Normally, our factory will be equipped with material testing instruments to find several points on the main body of the pipe fitting tee to detect whether the tee material is qualified.

  2. The appearance of the Gost 17376 Butt Welding Reducing Pipe Fitting Tee must be inspected before leaving the factory.

  In order to better meet customers' needs for Gost 17376 Butt Welding Reducing Pipe Fitting Tees, the appearance dimensions and appearance quality of Gost 17376 Butt Welding Reducing Pipe Fitting Tees must be inspected before leaving the factory to see if they are processed according to customer needs, whether the wall thickness is within a reasonable range, and whether there is any deviation in the caliber. Measure whether the length of the main branch pipe meets the standard; check whether there are cracks, rust, electric shock damage, local melting on the surface of the pipe fitting tee, whether the distribution of the quenching area is appropriate , and whether there are any defects such as scars that may affect use.

  If there are cracks on the Gost 17376 Butt Welding Reducing Pipe Fitting Tee, whether they are quenching cracks or material cracks, these two cracks are relatively small and are usually inspected by magnetic particle inspection; surface etching can be used, that is, using sandpaper to remove the surface coating or scale . Finally, use 10%~25% nitric acid alcohol solvent as a corrosive agent and apply it directly on the surface of the tee. After 10~20S, the surface of the pipe fitting tee can clearly show whether there are cracks, soft spots and hardened areas; macroscopic inspection, For induction hardened shaft tees with a diameter less than 25 or 30mm, grind a notch on a grinder, then break it with a hammer or press it with a press. Observe the fracture directly. The hardened layer in the fracture will show fine gray-white stubble (surface layer). The quenched part in the middle shows rough stubble.

  After a series of inspections, we will send away the qualified Gost 17376 Butt Welding Reducing Pipe Fitting Tees, and the unqualified Gost 17376 Butt Welding Reducing Pipe Fitting Tees will not be allowed to leave the factory.

Related News
Read More >>
DIN 2576 PN10 Slip On Flange Dimensions DIN 2576 PN10 Slip On Flange Dimensions
Nov .19.2026
DIN 2576 PN10 slip on flange is one of our core forged products at Hebei Shengtian Pipe-fitting Group. Fabricated to DIN 2576 specification, this slip-on flange is rated PN10, ideal for low-pressure piping connections.
DIN 2573 PN6 Slip On Flange Dimensions DIN 2573 PN6 Slip On Flange Dimensions
Nov .17.2026
DIN 2573 PN6 Slip On Flange is a popular slip-on plate flange following the DIN 2573 standard for low-pressure piping applications, rated for a nominal working pressure of 6 bar.
DIN 2545 PN40 Slip On Flange Dimensions DIN 2545 PN40 Slip On Flange Dimensions
Nov .12.2026
Hebei Shengtian Pipe Fittings Group Co., Ltd. supplies premium DIN 2545 PN40 Slip On Flanges
DIN 2544 PN25 Slip On Flange Dimensions DIN 2544 PN25 Slip On Flange Dimensions
Nov .10.2026
DIN 2544 specifies slip-on flanges rated at PN 25 .Covers sizes DN 10 to DN 1000.The flanges with the dimensions of this standard can be used at maximum 120°C temperature with up to 25 bar of working pressure.